Transaction fees may be included with any transfer of bitcoins from one address to another. Prior to 2015, many transactions were typically processed in a way where no fee was expected at all, however this changed in 2015 . Currently, for transactions which draw coins from many bitcoin addresses and therefore have a large data size, a small transaction fee is usually expected.
The transaction fee is processed by and received by the bitcoin miner. When a new bitcoin block is generated with a successful hash, the information for all of the transactions is included with the block and all transaction fees are collected by that user creating the block, who is free to assign those fees to himself.
Transaction fees are voluntary on the part of the person making the bitcoin transaction, as the person attempting to make a transaction can include any fee or none at all in the transaction. On the other hand, nobody mining new bitcoins necessarily needs to accept the transactions and include them in the new block being created. The transaction fee is therefore an incentive on the part of the bitcoin user to make sure that a particular transaction will get included into the next block which is generated.
It is envisioned that over time the cumulative effect of collecting transaction fees will allow somebody creating new blocks to "earn" more bitcoins than will be mined from new bitcoins created by the new block itself. This is also an incentive to keep trying to create new blocks even if the value of the newly created block from the mining activity is zero in the far future.
The following sections describe the behavior of the reference implementation as of version 0.10.0. Earlier versions treated fees differently, as do other popular implementations (including possible later versions).
A transaction may be safely sent without fees if these conditions are met:
- It is smaller than 1,000 bytes.
- All outputs are 0.01 BTC or larger.
- Its priority is large enough (see the Technical Info section below)
Otherwise, the reference implementation will round up the transaction size to the next thousand bytes and add a fee of 0.1 mBTC (0.0001 BTC) per thousand bytes. As an example, a fee of 0.1 mBTC (0.0001 BTC) would be added to a 746 byte transaction, and a fee of 0.2 mBTC (0.0002 BTC) would be added to a 1001 byte transaction. Users may increase the default 0.0001 BTC/kB fee setting, but cannot control transaction fees for each transaction. Bitcoin-Qt does prompt the user to accept the fee before the transaction is sent (they may cancel the transaction if they are not willing to pay the fee).
Note that a typical transaction is 500 bytes, so the typical transaction fee for low-priority transactions is 0.1 mBTC (0.0001 BTC), regardless of the number of bitcoins sent.
Including in Blocks
This section describes how the reference implementation selects which transactions to put into new blocks, with default settings. All of the settings may be changed if a miner wants to create larger or smaller blocks containing more or fewer free transactions.
50,000 bytes in the block are set aside for the highest-priority transactions, regardless of transaction fee. Transactions are added highest-priority-first to this section of the block.
Then transactions that pay a fee of at least 0.00001 BTC/kb are added to the block, highest-fee-per-kilobyte transactions first, until the block is not more than 750,000 bytes big.
The remaining transactions remain in the miner's "memory pool", and may be included in later blocks if their priority or fee is large enough.
The reference implementation's rules for relaying transactions across the peer-to-peer network are very similar to the rules for sending transactions, as a value of 0.00001 BTC is used to determine whether or not a transaction is considered "Free". However, the rule that all outputs must be 0.01 BTC or larger does not apply. To prevent "penny-flooding" denial-of-service attacks on the network, the reference implementation caps the number of free transactions it will relay to other nodes to (by default) 15 thousand bytes per minute.
|Setting||Default Value (units)|
|limitfreerelay||15 (thousand bytes per minute)|
Transaction priority is calculated as a value-weighted sum of input age, divided by transaction size in bytes:
priority = sum(input_value_in_base_units * input_age)/size_in_bytes
Transactions need to have a priority above 57,600,000 to avoid the enforced limit (as of client version 0.3.21). This threshold is written in the code as COIN * 144 / 250, suggesting that the threshold represents a one day old, 1 btc coin (144 is the expected number of blocks per day) and a transaction size of 250 bytes.
So, for example, a transaction that has 2 inputs, one of 5 btc with 10 confirmations, and one of 2 btc with 3 confirmations, and has a size of 500bytes, will have a priority of
(500000000 * 10 + 200000000 * 3) / 500 = 11,200,000